CHANGE UR IP
How To: Change Your Ip In Less Then 1 Minute
1. Click on "Start" in the bottom left hand corner of screen
2. Click on "Run"
3. Type in "command" and hit ok You should now be at an MSDOS prompt screen.
4. Type "ipconfig /release" just like that, and hit "enter"
5. Type "exit" and leave the prompt
6. Right-click on "Network Places" or "My Network Places" on your desktop.
7. Click on "properties" You should now be on a screen with something titled "Local Area Connection", or something close to that, and, if you have a network hooked up, all of your other networks.
8. Right click on "Local Area Connection" and click "properties"
9. Double-click on the "Internet Protocol (TCP/IP)" from the list under the "General" tab
10. Click on "Use the following IP address" under the "General" tab1
1. Create an IP address (It doesn't matter what it is. I just type 1 and 2 until i fill the area up).
12. Press "Tab" and it should automatically fill in the "Subnet Mask" section with default numbers.
13. Hit the "Ok" button here
14. Hit the "Ok" button again
You should now be back to the "Local Area Connection" screen.
15. Right-click back on "Local Area Connection" and go to properties again.
16. Go back to the "TCP/IP" settings
17. This time, select "Obtain an IP address automatically"tongue.gif
18. Hit "Ok"
19. Hit "Ok" again
20. You now have a new IP address
With a little practice, you can easily get this process down to 15 seconds.
This only changes your dynamic IP address, not your ISP/IP address. If you plan on hacking a website with this trick be extremely careful, because if they try a little, they can trace it back Easy way.click the LAN icon on the tray....click properties...then click INTERNET PROTOCOL....click properties....here u are...
Insert Image In Your Mail Signature
To add a graphic to your email signature in Yahoo! Mail:
1. Access Yahoo! Mail wit Windows Internet Explorer.
2. Select Mail Options from the navigation bar.
3. Follow the Signature link.
4. If the HTML toolbar is not yet visible, click Color and Graphics.
5. Make sure View HTML Source is checked.
6. Insert the image using the HTML tag.
To place an image at the left of your signature, insert
'
7. Make sure the image is accessible on a web server and reasonably small in proportions (not higher than about 75 pixels).
8. Uncheck View HTML Source to test your signature.
9.Click Save.
Increase internet speed
Click Start then Run and type "gpedit.msc" without quotes.
This opens the "group policy editor" and go to: "Local Computer Policy"
Then "Computer Configuration" Then "Administrative Templates"
Then select "Network" then "QOS Packet Scheduler"
After that select "Limit Reservable Bandwidth".
Double click on Limit Reservable bandwidth. It will say it is not configured, but the truth is under the 'Explain' tab i.e.” By default, the Packet Scheduler limits the system to 20 percent of the bandwidth of a connection, but you can use this setting to override the default."
So the trick is to ENABLE reservable bandwidth, then set it to ZERO. This will allow the system to reserve nothing, rather than the default 20%.
Remove Yahoo Ads
If you install the newest Yahoo Messenger 7.5 + & Version 8
you'll notice a very annoying animated ads at the bottom of the main window.
To remove the Ads! Here is the Procedure!
(1)Open Notepad,
(2) Paste the following code on Notepad and save it as: somename.reg
Code: REGEDIT4
[HKEY_CURRENT_USER\Software\Yahoo\pager\YUrl]
"N2Phone Adurl"="*"
"Messenger Ad"="*"
"Address Book"="*"
"Change Room Banner"="*"
"Conf Adurl"="*"
"Chat Adurl"="*"
"Tutorials"="*"
"Messenger Help"="*"
"Voice General Help"="*"
"Finance Disclaimer"="*"
"Webcam Upload Ad"="*"
"Webcam Viewer Ad"="*"
"Webcam Viewer Ad Big"="*"
"Webcam Viewer Ad Medium"="*"
"News Alert Ad URL"="*"
(3)Double click the file ( say: somename.reg )
(4)Click Yes
Its Done!! No more ads will be there in the yahoo messenger Window!
Trace the route
A great utility included with Windows is a program called Trace Route. Open a DOS window and type tracert . The location name can be any IP address or Internet domain like tracert .The program will then trace the route from your Internet service provider to that locating, and show you every server along the way. This could be useful for when you can't connect to a site it will show you if some server is down along the way
Backing Up Your ISP Settings
If you want to save your ISP settings (name, phone, login id etc.) for future installations: Start Regedit
Go to HKEY_CURRENT_USER \ RemoteAccess
Select Registry / Export Registry
Make sure Selected branch is checked
For the name, enter any name that will help you remember the purpose of the .reg file
Now if you need to restore your ISP settings after a new installation of Windows, you just need to import this file
Internet TIPS
Subscribe to:
Post Comments (Atom)
0 comments:
Post a Comment